發熱電纜電供暖系統安裝完成后需要對整個系統進行運行測試、調試等必要的步驟才可以通電使用。在發熱電纜電供暖系統鋪設完畢后，按設計要求檢查是否符合設計要求并用電表和搖表檢測發熱電纜的電阻值和絕緣電阻值是否正常且符合規定值，確保發熱電纜無短路、斷路現象。
然后是發熱電纜上的混凝土層的填充鋪設，混凝土層需均勻鋪設厚度在25-50mm之間。發熱電纜電供暖系統中的混凝土層完工后48小時內請勿踩踏，填充層在施工完畢后的地面嚴禁剔鑿、重載等。混凝土層施工完畢后，再用電表和搖表檢測每根發熱電纜，以檢查發熱電纜在施工過程中有無損壞。接著可以再進行地面裝飾材料的鋪設，地面裝飾材料在鋪設時嚴禁在鋪有發熱電纜的區域進行裝飾材料的切割，嚴禁在有發熱電纜的區域打釘以防造成發熱電纜的損壞。地面裝飾材料鋪設完畢后，再用萬用表和搖表檢測發熱電纜，以防止發熱電纜在地面裝飾材料施工過程中出現損壞。
發熱電纜電供暖系統中的溫控器應在工程交付使用前進行安裝，以免在施工造成損壞。安裝時以電地暖溫控器安裝使用說明書為準，安裝完成后通電檢測。溫控器的調試應按不同種類溫控器安裝調試說明書進行。
