根據鍍件表面積和鍍件的重童選擇銅絲的直徑，應在能使電流正常暢通，并能承受懸掛重談的前提下，盡最小一點.銅絲過粗，除對鍍件會造成過大面積的遮蓋之外，還可能導致鍍件變形;銅絲過細，除承受不了鍍件重量外，還可能影響到所需電流的通過而不能獲得正常的鍍層質量。另外，受鍍的鍍種也是應考慮的因素。例如，在綁扎鍍亮鎳件時，銅絲不宜選得過細。因為亮鎳很脆，若鋼絲過分細小。就有可能在電鍍時因陰極棒的移動或鍍件出枯時受力而被折斷。當綁扎已經鍍鎳并經拋光過的裝飾性鍍鉻件時，所用的銅絲則宜適當選得細點，以減輕銅絲在鍍件上的遮蓋面，且該銅絲應先經鍍一層鉻才可使用，否則綁扎處難免產生銅絲影。一般情況下，不宜用雙股鋼絲綁扎鍍件，否則極容易產生銅絲影。